استانداردها

استاندردهای پلی اتیلن,PVC,پلاستیک و استانداردهای پلیمر از آن دسته استانداردهایی است که به سختی در اختیار متخصصین قرار میگیرد و جامعه متخصصین همیشه در بدست آوردن آخرین نسخه‌های معتبر استانداردها جهت انجام محاسبات و انتخاب اجناس پروژه‌ها دچار مشکل بوده است .

 

استانداردهای ISO

استاندارد ISO
ISO 4427 : Polyethylene (PE) pipes for water supply – specifications

ISO 4427-1 :Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General

ISO 4427-1 :Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General TECHNICAL CORRIGENDUM 1

ISO 4427-2 :Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes

ISO 4427-3 : Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings

 

ISO 4437 : Buried polyethylene (PE) pipes for the supply of gaseous fuels- Metric series – specifications

ISO 442-2 : Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2:Pipes

ISO 1969 : Fibre Ropes – polyethylene – 3- and 4 strand ropes

ISO 2268 : Surface active agents (non Ionic) -Determination of polyethylene glycols and non ionic active matter (Adducts)-Weibull method

ISO 3458 : Assembled joints between fittings and polyethylene (PE) Pressure pipes – test of leakproofness under internal pressure

ISO 3459 : Polyethylene (PE) Pressure pipes – joints assembled with mechanical fitting- Internal under-Pressure test method and requirment

ISO 3501 : Assembled joints between fittings and polyethylene )PE) pressure pipes- Test of resistance to pull out

ISO 3503 : Assembled joints between fittings and polyethylene (PE) pressure pipes-Test of leakproofness under internal pressure when subjected to bending

ISO 3633 : UPVC pipes and fittings for soil and wasfe discharge (low and high temperature) Systems inside buildings – Specifications

ISO 3663 : Polyethylene (PE) pressure pipes and fittings, metric series – Dimensions of flanges

ISO 4059 : polyethylene (PE) pipes – pressure drop in Mechanical pipe-jointing systems – method of test and requirments

ISO 6402-2 : Plastics -Acrylonitrile styrene acrylate (ASA), acrylonitrile (ethylene propylene diene) styrene (AEPDS) and acrylonitrile (Chlorinated polyethylene) styrene (ACS) moulding and extrusion materials , Part 2: Preparation of test speciments and detemination of properties

ISO 7214 : Cellular Plastics – Polyethylene – Methods of test

ISO 8005-3 : Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels – metric series – Specifications , Part 3: Electrofusion fittings

ISO 8180 : Ductile iron pipes – polyethylene sleeving

ISO 8283-2 : Plastics pipes and fittings – Dimensions of sockets and spigots for discharge systems inside buildings , Part 2: Polyethylene

ISO 8770 : Plastics piping systems for soil and waste discharge (Low and high temperature) inside buildings – Polyethylene

ISO 8772 : High density Polyethylene (HDPE) pipes and fittings for buried drainage and sewerage systems -Specifications

ISO 8796 : Polyethylene PE 32 and PE 40 pipes for irrigation laterals — Susceptibility to environmental stress cracking induced by insert-type fittings — Test method and requirements

ISO 9625:Mechinal Joint fittings for use eith polyethylene pressure pipes for irrigation purposes

ISO 10933 : Polyethylene (PE) valves for gas distribution systems

ISO 11413 : Plastics pipe and fittings – preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

ISO 11414 : Plastics pipes and fittings – preparation of polyethylene (PE) pipe / pipe or pipe/fitting test piece assemblies by butt fusion

ISO 13460 : Agricultural irrigation equipment – plastics saddles for polyethylene pressure pipes

ISO 13480 : polyethylene pipes – resistance to slow crack growth – Cone test method

ISO 13761 : Plastics pipes and fittings – pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 C

ISO 13954 : Plastics pipes and fittings – peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

ISO 13955 : Plastics pipes and fittings – crushing decohesion test for polyethylene (PE) electro fusion assemblies

ISO 13957 : Plastics pipes and fittings – polyethylene (PE) tapping tees – Test method for impact resistance

ISO 14236 : Plastics pipes and fittings – mechanical joint compression fittings for use with polyethylene pressure pipes in water supply systems

ISO 14531 – 2 : Plastics pipes and fittings – Crosslinked polyethylene (PEX) pipe systems for the conveyance of gaseous fuels – Metric series- Specifications , Part2 : Fittings fir heat fusion jointing

ISO 15875-1 : Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PEX) ,Part 1: General

ISO 15875-2 : Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PEX) ,Part 2: Pipes

ISO 15875-3 : Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PEX) ,Part 3: Fittings

ISO 15875-5 : Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PEX) ,Part 5: Fitness for purpose of the system

ISO 16241 : Notch tensile test to measure the resistance to slow crack growth of polyethylene materials for pipe and fitting products-PENT

ISO 161-1 : Thermoplastics pipes for the conveyance of fluids – Nominal outside diameters and nominal pressures , Part 1:Metric Series

ISO 264 :Unplasticized Polyvinyl chloride (PVC) Fittings With plain Sockets for pipes under pressure -laying length-Metric series

ISO 727 : Fittings of unplasticized polyvinyl chloride (UPVC),chlorinated polyvinyl chloride (CPVC) or acrylonitrile/butadiene/styrene (ABS) with plain socjets for pipes under pressure – Dimensions of sockets – Metric series

ISO 727-1 : Fittings made from unplasticized poly(vinyl chloride)(UPVC), chlorinated poly vinyl chloride (CPVC) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure, Part 1: Metric Series

ISO 727-2 : Fittings made from unplasticized poly(vinyl chloride)(UPVC), chlorinated poly vinyl chloride (CPVC) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure, Part 2: Inch Based series

ISO 1167 : Thermoplastics pipes for the conveyance of fluids-Resistance to internal pressure – test method

ISO 1167-1 :Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method

ISO 1167-2 : Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces

ISO 3663 : Polyethylene (PE) Pressure pipes and fittings, Metric series , Dimensions of flanges

ISO 4433-1: Thermoplastics Pipes – Resistance to liquid chemicals – Classification , Part 1 : Immersion test method

ISO 4433-2: Thermoplastics Pipes – Resistance to liquid chemicals – Classification , Part 2 : Polyolefin pipes

ISO 4433-3: Thermoplastics Pipes – Resistance to liquid chemicals – Classification , Part 3 : Upvc,Hi-PVC , CPVC

ISO 4433-4: Thermoplastics Pipes – Resistance to liquid chemicals – Classification , Part 4 : poly (vinylidene fluoride)(PVDF) pipes

ISO 4433-COR1: Buried polyethylene (PE) pipes for the supply of gaseous fuels — Metric series — Specifications ,TECHNICAL CORRIGENDUM 1

ISO 9080 : Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation

ISO 9623 : PE/metal and PP/metal adaptor fittings for pipes for fluids under pressure – Design lengths and size of threads- Metric Series

ISO 9624 : Thermoplastics pipes for fluids under pressure-Mating dimensions of flange adapters and loose backing flanges

ISO 12162 : Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient

ISO 12167-1 : Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion

ISO 12167-2 : Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion

ISO 12167-3 : Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 3:Operator`s badge

ISO 12167-4 : Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4:Traceability coding

ISO 13477 : Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)

ISO 13478 : thermoplastics pipes for the conveyance of fluids Determination of resistance to rapid crack propagation (RCP) – Full scale test

ISO 13479 : Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes

ISO 13480 : Polyethylene pipes – resistance to slow crack growth-Cone test method

ISO 13761 : Plastics pipes and fittings – pressure reduction factors for polyethylene pipeline systeme for use at temperatures above 20 C

ISO 14236 : Plastics pipes and fittings — Mechanicaljoint compression fittings for use with polyethylene pressure pipes in water supply systems

ISO 10358 – TR : Plastic pipes and fittings-Combined chemical-resistance classification table

ISO 10837 – TR : Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings

ISO 11295 – TR : techniques for rehabilitation of pipeline systems by the use of plastics pipes and fittings

ISO 11647 – TR : Fusion Compatibility of polyethylene (PE) pipe and fittings

ISO 13950 – TR : Plastics Pipes and fittings – Automatic recognition systems for electrofusion

Post comment : 1
  • نگاهبان
    نگاهبان says نوامبر 11, 2018 at 2:39 ب.ظ

    YOUR COMMENT…

دیدگاهتان را بنویسید
Open chat
چت واتساپ
✔ درخواست خود را مطرح نمائید.